I figure I can get a new prop for the price of a few dozen pins. Therefore, the prop will take the brunt of any accidents. The nails are slightly softer than the pins, so they tend to bend rather than break. I grabbed a hacksaw and cut them to length. An hour later I found a few nails that looked like they would do the job, or at least get us home if needed. Eventually I got tired of buying kits and I began to look around the garage for rods similar in diameter. Several trips later I needed more, so I ordered another kit. The trolling motor pins were softer than the original pins for the motor, so they broke/sheared much easier. I picked up a kit for $12 which contained two pins.
All I could find was a pin made for a trolling motor, Bass Pro's "Prowler" series. Anyone familiar with the Jiffy ice augers will knwo these are the same platform with all motor parts available. These are tecumseh air cooled motors made in Grafton, WI. Light, powerful motor, I cleaned it up redid the carb and fuel lines, changed lower unit oil, runs perfect.
7.5 hp ted williams outboard motor pro#
So I made a trip to Bass Pro to find a pin that would replace the one in the outboard. 1976 Ted Williams Sears 7.5 hp 2 stroke outboard ESKA Gamefisher. The pin is made to break when the prop encounters a hard surface such as a boulder, tree, etc. It also fits all Sears/Gamefisher outboard motors 7.5 hp thru 15 hp from 1986-1997. For a lack of better words, I guess what we did when trying to travel up the shallow riffle was comparable to shearing a pin. This is the impeller needed when repairing your water pump on the following Montgomery Wards/Sea King outboard motors with the starting letters VWB in the model number: 9.9 hp from 1980-1986, 10 hp from 1974-1976, and 15 hp from 1974-1986. Nos Sears Elgin Outboard Motor Reed Plate Block A36158 West Bend Chrysler. Nos Sears Elgin Outboard Motor Fuel Petcock Shut Off Valve West Bend Chrysler 3.
That's when it hit me, when I bailed hay for my first time I "sheared pins" on the power take off. 60s Sears Ted Williams 7.5 Hp Outboard Flywheel Motor Model Mcculloch 574.60607. Parting out a mid-1970s, 7.5hp, 2 stroke Ted Williams outboard sold by Sears, manufactured by Eska, and powered by an air cooled, single cylinderTecumseh engine. I took the prop off and noticed that the propeller was driven by a single pin. Parts off a mid 70s 7.5 hp Ted Williams outboard motor. When I got home I took the motor apart and started to analyze every part. So we trolled 2 hours back to the ramp in the rain later that night. While trying to navigate an extremely shallow riffle, the outboard motor hit a couple rocks and the prop quit spinning, the motor still ran but the prop wouldn't spin. We have since found a public ramp further upstream. We put the boat in at the boat ramp near the Ohio River and drove upstream for an hour and a half looking for good looking catfish spots. Sears/Gamefisher: 7.A month and a half ago Rylan, Amanda, and I took the boat out to Brush Creek and ran into a few issues on along the way.Also this WILL NOT FIT TED WILLIAMS OR ESKA MODELS!! APPLICATION: NOTE: this will not fit model numbers starting with 217. These impellers are new factory fresh - NOT old parts that have been sitting around collecting dust & dry rotting! This is the impeller needed when repairing your water pump on the following Montgomery Wards/Sea King outboard motors with the starting letters VWB in the model number: 9.9 hp from 1980-1986, 10 hp from 1974-1976, and 15 hp from 1974-1986.
7.5 hp ted williams outboard motor free#
Sale Price for this item includes FREE SHIPPING. Click the "PURCHASE HERE" link below to buy this item (you will be redirected to our EBAY page for this item)